EEPROM spec requests this.

v2: Only to be done for write data transactions.

Signed-off-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Not sure how the firmware interprets these.

Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Handle things besides EEPROMS.

Signed-off-by: Aaron Rice <wolf@lovehindpa.ws>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Not sure that this really matters that much, but these could
have various other hwmon chips on them.

Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Convert from 8 bit to 7 bit.

Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Use the new helper rather than doing i2c transfers directly.

v2: fix typo

Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Use the new helper rather than doing i2c transfers directly.

Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Encapsulates the i2c protocol handling so other parts of the
driver can just tell it the offset and size of data to write.

Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

And handle more than just EEPROMs.

v2: fix restart handling between transactions.
v3: handle 7 to 8 bit addr conversion

Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Make it generic so we can support more than just EEPROMs.

v2: fix restart handling between transactions.
v3: handle 7 to 8 bit addr conversion

Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Make it generic so we can support more than just EEPROMs.

v2: fix restart handling between transactions.
v3: handle 7 to 8 bit addr conversion

Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

So we lock software as well as hardware access to the bus.

v2: fix mutex handling.

Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

We are able to power down the GPU and audio via the GPU driver
so flag these asics as supporting runtime pm.

Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

HP Elite Disk 705 G4 Micro seems to have issues with gfxoff.

Bug: https://bugzilla.kernel.org/show_bug.cgi?id=207899


Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]
Following the spec of UCSI, EC may return CCI_BUSY for PPM reset cmd.

[How]
Check CCI_BUSY bit.

Jira ID: SCSWATH-10
Signed-off-by: Liang Liang (Leo) <liang.liang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

The ip discovery is supported on green sardine, it doesn't need gpu info
firmware anymore.

Signed-off-by: Huang Rui <ray.huang@amd.com>
Reviewed-by: Prike Liang <Prike.Liang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

ROCm user mode depends on userptr support. Without it, KFD is basically
useless.

Make sure HSA_AMD selects the same options as DRM_AMDGPU_USERPTR to avoid
broken configurations where userptr gets enabled but its dependencies are
disabled.

Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Reviewed-by: Philip Yang <philip.yang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

This patch is to help firmware designer to know the smc message timeout
status.

Signed-off-by: Huang Rui <ray.huang@amd.com>
Reviewed-by: Kevin Wang <kevin1.wang@amd.com>
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Add PCIE_SPEED_32_0GT and PCIE GEN5 support for amdgpu.

Signed-off-by: Feifei Xu <Feifei.Xu@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Send allow GfxOff message to SMU to enter GfxOff
mode as default.

Signed-off-by: Jinzhou Su <Jinzhou.Su@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Fix the following coccicheck warnings:

./drivers/gpu/drm/amd/display/dc/dml/dcn30/display_rq_dlg_calc_30.c:
1009:6-16: WARNING: Assignment of 0/1 to bool variable.

./drivers/gpu/drm/amd/display/dc/dml/dcn30/display_rq_dlg_calc_30.c:
200:2-10: WARNING: Assignment of 0/1 to bool variable.

Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Jiapeng Zhong <abaci-bugfix@linux.alibaba.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

There are two spelling mistakes of the function name, fix this
by using __func__ instead of a hard coded name string.

Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Update the function for idle optimizations
-remove hardcoded size
-enable no memory-request case
-add cursor copy
-update mall eligibility check case

Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Joshua Aberback <joshua.aberback@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]
Currently we use the maximum possible cursor cache size when deciding if we
should attempt to enable MALL, but this prevents us from enabling the
feature for certain key use cases.

[How]
 - consider cursor bpp when calculating if the cursor fits

Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Joshua Aberback <joshua.aberback@amd.com>
Reviewed-by: Aric Cyr <aric.cyr@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

-Uncomment watermark set d
-This populates the wm table so that it can be sent to PMFW
-This watermark table is used when we are in mall stutter

Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Starting from vangogh, the ATCL2 and DAGB0 registers relative
to mgcg/ls has changed.

For MGCG:
Replace mmMM_ATC_L2_MISC_CG with mmMM_ATC_L2_CGTT_CLK_CTRL.

For MGLS:
Replace mmMM_ATC_L2_MISC_CG with mmMM_ATC_L2_CGTT_CLK_CTRL.
Add DAGB0_(WR/RD)_CGTT_CLK_CTRL registers.

Signed-off-by: Aaron Liu <aaron.liu@amd.com>
Acked-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Driver should enable the CGPG feature for RLC in safe mode to
prevent any misalignment or conflict in middle of any power
feature entry/exit sequence.
Achieved by setting RLC_PG_CNTL.GFX_POWER_GATING_ENABLE = 0x1,
and RLC_PG_DELAY_3.CGCG_ACTIVE_BEFORE_CGPG to the desired CGPG
hysteresis value in refclk count.

Reviewed-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Jinzhou Su <Jinzhou.Su@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

In the renoir there is no need GpuChangeState message set to exit gfxoff in the s0i3 resume since
mmnbif_gpu_BIF_DOORBELL_FENCE_CNTL has been added in the s0i3 FSDL.

Signed-off-by: Prike Liang <Prike.Liang@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

GCR_GENERAL_CNTL is defined differently in gc_10_1_0_offset.h and
gc_10_3_0_offset.h. Update GCR_GENERAL_CNTL for Vangogh.

Signed-off-by: Jinzhou Su <Jinzhou.Su@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

 1. Remove PP_GFXOFF_MASK and then GFXOFF can be enabled
    by user space.
 2. GFXOFF is still disabled on Vangogh by default.
 3. When GFXOFF feature on Vangogh landed, will enable
    GFXOFF by default.
 4. GFXOFF can be enabled by debugfs interface amdgpu_gfxoff.

Signed-off-by: Jinzhou Su <Jinzhou.Su@amd.com>
Acked-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Acked-by: Anson Jacob <anson.jacob@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Anson Jacob <anson.jacob@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[WHY]
dram clock change latencies get updated using ddr4 latency table, but
that update does not happen before validation. This value
should not be the default and should be number received from
df for better mode support.
This may cause a PState hang on high refresh panels with short vblanks
such as on 1080p 360hz or 300hz panels.

[HOW]
Update latency from 23.84 to 11.72.

Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Jake Wang <haonan.wang2@amd.com>
Reviewed-by: Sung Lee <Sung.Lee@amd.com>
Acked-by: Anson Jacob <anson.jacob@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]
When no displays are currently enabled, display driver should not
disallow PSTATE switching.

[How]
Allow PSTATE switching if either the active configuration supports it,
or there are no active displays.

Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Anson Jacob <anson.jacob@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Why:
dml20v2_ModeSupportAndSystemConfigurationFull() didn't check against
DesiredBPP, so it doesn't work correctly when DesiredBPP can't be satisfied.

How:
Port the TruncToValidBPP() version from display_mode_vba_21.c to
display_mode_vba_20v2.c.

Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Bing Guo <bing.guo@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Anson Jacob <anson.jacob@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why/How]
Add logging statements to assist in debugging
errors in the BIOS object table.

Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: George Shen <george.shen@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Anson Jacob <anson.jacob@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]
FW version check doesn't allow dmu_stg to support cached inbox,
which yields much better performance than region 4.

[How]
Check a range of fw versions, rather than a simple greater than check.

Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Wyatt Wood <wyatt.wood@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Anson Jacob <anson.jacob@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Why:
Function decide_dp_link_settings() loops infinitely when required bandwidth
can't be supported.

How:
Check the required bandwidth against verified_link_cap before trying to
find a link setting for it.

Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Bing Guo <bing.guo@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Anson Jacob <anson.jacob@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]
DMCUB encounters a page fault/double exception with driver direct load
because DMCUB is not held in soft reset after releasing secure reset.

The clean shutdown sequence via GPINT is also not executed in this
sequence which leaves hardware behavior in an indeterminate state.

[How]
Move reset earlier in the sequence.

Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Anson Jacob <anson.jacob@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]
If the BIOS table is invalid or corrupt then get_i2c_info can fail
and we dereference a NULL pointer.

[How]
Check that ddc_pin is not NULL before using it and log an error if it
is because this is unexpected.

Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Anson Jacob <anson.jacob@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>