Commit bb0a56ec authored by Dave Jones's avatar Dave Jones

[CPUFREQ] Move x86 drivers to drivers/cpufreq/

Signed-off-by: default avatarDave Jones <davej@redhat.com>
parent 1a8e1463
......@@ -1848,7 +1848,7 @@ config APM_ALLOW_INTS
endif # APM
source "arch/x86/kernel/cpu/cpufreq/Kconfig"
source "drivers/cpufreq/Kconfig"
source "drivers/cpuidle/Kconfig"
......
......@@ -30,7 +30,6 @@ obj-$(CONFIG_PERF_EVENTS) += perf_event.o
obj-$(CONFIG_X86_MCE) += mcheck/
obj-$(CONFIG_MTRR) += mtrr/
obj-$(CONFIG_CPU_FREQ) += cpufreq/
obj-$(CONFIG_X86_LOCAL_APIC) += perfctr-watchdog.o
......
# Link order matters. K8 is preferred to ACPI because of firmware bugs in early
# K8 systems. ACPI is preferred to all other hardware-specific drivers.
# speedstep-* is preferred over p4-clockmod.
obj-$(CONFIG_X86_POWERNOW_K8) += powernow-k8.o mperf.o
obj-$(CONFIG_X86_ACPI_CPUFREQ) += acpi-cpufreq.o mperf.o
obj-$(CONFIG_X86_PCC_CPUFREQ) += pcc-cpufreq.o
obj-$(CONFIG_X86_POWERNOW_K6) += powernow-k6.o
obj-$(CONFIG_X86_POWERNOW_K7) += powernow-k7.o
obj-$(CONFIG_X86_LONGHAUL) += longhaul.o
obj-$(CONFIG_X86_E_POWERSAVER) += e_powersaver.o
obj-$(CONFIG_ELAN_CPUFREQ) += elanfreq.o
obj-$(CONFIG_SC520_CPUFREQ) += sc520_freq.o
obj-$(CONFIG_X86_LONGRUN) += longrun.o
obj-$(CONFIG_X86_GX_SUSPMOD) += gx-suspmod.o
obj-$(CONFIG_X86_SPEEDSTEP_ICH) += speedstep-ich.o
obj-$(CONFIG_X86_SPEEDSTEP_LIB) += speedstep-lib.o
obj-$(CONFIG_X86_SPEEDSTEP_SMI) += speedstep-smi.o
obj-$(CONFIG_X86_SPEEDSTEP_CENTRINO) += speedstep-centrino.o
obj-$(CONFIG_X86_P4_CLOCKMOD) += p4-clockmod.o
obj-$(CONFIG_X86_CPUFREQ_NFORCE2) += cpufreq-nforce2.o
menu "CPU Frequency scaling"
config CPU_FREQ
bool "CPU Frequency scaling"
help
......@@ -177,4 +179,10 @@ config CPU_FREQ_GOV_CONSERVATIVE
If in doubt, say N.
endif # CPU_FREQ
menu "x86 CPU frequency scaling drivers"
depends on X86
source "drivers/cpufreq/Kconfig.x86"
endmenu
endif
endmenu
#
# CPU Frequency scaling
# x86 CPU Frequency scaling drivers
#
menu "CPU Frequency scaling"
source "drivers/cpufreq/Kconfig"
if CPU_FREQ
comment "CPUFreq processor drivers"
config X86_PCC_CPUFREQ
tristate "Processor Clocking Control interface driver"
depends on ACPI && ACPI_PROCESSOR
......@@ -261,6 +253,3 @@ config X86_SPEEDSTEP_RELAXED_CAP_CHECK
option lets the probing code bypass some of those checks if the
parameter "relaxed_check=1" is passed to the module.
endif # CPU_FREQ
endmenu
......@@ -13,3 +13,29 @@ obj-$(CONFIG_CPU_FREQ_GOV_CONSERVATIVE) += cpufreq_conservative.o
# CPUfreq cross-arch helpers
obj-$(CONFIG_CPU_FREQ_TABLE) += freq_table.o
##################################################################################d
# x86 drivers.
# Link order matters. K8 is preferred to ACPI because of firmware bugs in early
# K8 systems. ACPI is preferred to all other hardware-specific drivers.
# speedstep-* is preferred over p4-clockmod.
obj-$(CONFIG_X86_POWERNOW_K8) += powernow-k8.o mperf.o
obj-$(CONFIG_X86_ACPI_CPUFREQ) += acpi-cpufreq.o mperf.o
obj-$(CONFIG_X86_PCC_CPUFREQ) += pcc-cpufreq.o
obj-$(CONFIG_X86_POWERNOW_K6) += powernow-k6.o
obj-$(CONFIG_X86_POWERNOW_K7) += powernow-k7.o
obj-$(CONFIG_X86_LONGHAUL) += longhaul.o
obj-$(CONFIG_X86_E_POWERSAVER) += e_powersaver.o
obj-$(CONFIG_ELAN_CPUFREQ) += elanfreq.o
obj-$(CONFIG_SC520_CPUFREQ) += sc520_freq.o
obj-$(CONFIG_X86_LONGRUN) += longrun.o
obj-$(CONFIG_X86_GX_SUSPMOD) += gx-suspmod.o
obj-$(CONFIG_X86_SPEEDSTEP_ICH) += speedstep-ich.o
obj-$(CONFIG_X86_SPEEDSTEP_LIB) += speedstep-lib.o
obj-$(CONFIG_X86_SPEEDSTEP_SMI) += speedstep-smi.o
obj-$(CONFIG_X86_SPEEDSTEP_CENTRINO) += speedstep-centrino.o
obj-$(CONFIG_X86_P4_CLOCKMOD) += p4-clockmod.o
obj-$(CONFIG_X86_CPUFREQ_NFORCE2) += cpufreq-nforce2.o
##################################################################################d
Markdown is supported
0% or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment