Commit 8ba3f4d0 authored by Sherman Yin's avatar Sherman Yin Committed by Linus Walleij

pinctrl: Adds slew-rate, input-enable/disable

This commit adds slew-rate and input-enable/disable support for pinconf
-generic.
Signed-off-by: default avatarSherman Yin <syin@broadcom.com>
Signed-off-by: Linus Walleij's avatarLinus Walleij <linus.walleij@linaro.org>
parent b31d100e
......@@ -151,6 +151,8 @@ drive-push-pull - drive actively high and low
drive-open-drain - drive with open drain
drive-open-source - drive with open source
drive-strength - sink or source at most X mA
input-enable - enable input on pin (no effect on output)
input-disable - disable input on pin (no effect on output)
input-schmitt-enable - enable schmitt-trigger mode
input-schmitt-disable - disable schmitt-trigger mode
input-debounce - debounce mode with debound time X
......@@ -158,6 +160,7 @@ low-power-enable - enable low power mode
low-power-disable - disable low power mode
output-low - set the pin to output mode with low level
output-high - set the pin to output mode with high level
slew-rate - set the slew rate
Some of the generic properties take arguments. For those that do, the
arguments are described below.
......
......@@ -48,6 +48,7 @@ static struct pin_config_item conf_items[] = {
PCONFDUMP(PIN_CONFIG_DRIVE_OPEN_DRAIN, "output drive open drain", NULL),
PCONFDUMP(PIN_CONFIG_DRIVE_OPEN_SOURCE, "output drive open source", NULL),
PCONFDUMP(PIN_CONFIG_DRIVE_STRENGTH, "output drive strength", "mA"),
PCONFDUMP(PIN_CONFIG_INPUT_ENABLE, "input enabled", NULL),
PCONFDUMP(PIN_CONFIG_INPUT_SCHMITT_ENABLE, "input schmitt enabled", NULL),
PCONFDUMP(PIN_CONFIG_INPUT_SCHMITT, "input schmitt trigger", NULL),
PCONFDUMP(PIN_CONFIG_INPUT_DEBOUNCE, "input debounce", "usec"),
......@@ -160,6 +161,8 @@ static struct pinconf_generic_dt_params dt_params[] = {
{ "drive-open-drain", PIN_CONFIG_DRIVE_OPEN_DRAIN, 0 },
{ "drive-open-source", PIN_CONFIG_DRIVE_OPEN_SOURCE, 0 },
{ "drive-strength", PIN_CONFIG_DRIVE_STRENGTH, 0 },
{ "input-enable", PIN_CONFIG_INPUT_ENABLE, 1 },
{ "input-disable", PIN_CONFIG_INPUT_ENABLE, 0 },
{ "input-schmitt-enable", PIN_CONFIG_INPUT_SCHMITT_ENABLE, 1 },
{ "input-schmitt-disable", PIN_CONFIG_INPUT_SCHMITT_ENABLE, 0 },
{ "input-debounce", PIN_CONFIG_INPUT_DEBOUNCE, 0 },
......@@ -167,6 +170,7 @@ static struct pinconf_generic_dt_params dt_params[] = {
{ "low-power-disable", PIN_CONFIG_LOW_POWER_MODE, 0 },
{ "output-low", PIN_CONFIG_OUTPUT, 0, },
{ "output-high", PIN_CONFIG_OUTPUT, 1, },
{ "slew-rate", PIN_CONFIG_SLEW_RATE, 0},
};
/**
......
......@@ -61,6 +61,9 @@
* argument is ignored.
* @PIN_CONFIG_DRIVE_STRENGTH: the pin will sink or source at most the current
* passed as argument. The argument is in mA.
* @PIN_CONFIG_INPUT_ENABLE: enable the pin's input. Note that this does not
* affect the pin's ability to drive output. 1 enables input, 0 disables
* input.
* @PIN_CONFIG_INPUT_SCHMITT_ENABLE: control schmitt-trigger mode on the pin.
* If the argument != 0, schmitt-trigger mode is enabled. If it's 0,
* schmitt-trigger mode is disabled.
......@@ -101,6 +104,7 @@ enum pin_config_param {
PIN_CONFIG_DRIVE_OPEN_DRAIN,
PIN_CONFIG_DRIVE_OPEN_SOURCE,
PIN_CONFIG_DRIVE_STRENGTH,
PIN_CONFIG_INPUT_ENABLE,
PIN_CONFIG_INPUT_SCHMITT_ENABLE,
PIN_CONFIG_INPUT_SCHMITT,
PIN_CONFIG_INPUT_DEBOUNCE,
......
Markdown is supported
0% or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment