Commit 72e9baf9 authored by Amit Kucheria's avatar Amit Kucheria Committed by Zhang Rui

drivers: thermal: Move QCOM_SPMI_TEMP_ALARM into the qcom subdir

This cleans up the directory a bit allowing just one place to look for
thermal related drivers for QCOM platforms instead of being scattered in
the root directory and the qcom/ subdirectory. Compile-tested with
ARCH=arm64 defconfig and the driver explicitly enabled with menuconfig.
Signed-off-by: default avatarAmit Kucheria <amit.kucheria@linaro.org>
Acked-by: default avatarDaniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: default avatarZhang Rui <rui.zhang@intel.com>
parent 3e8c4d31
......@@ -374,17 +374,6 @@ config TANGO_THERMAL
source "drivers/thermal/tegra/Kconfig"
config QCOM_SPMI_TEMP_ALARM
tristate "Qualcomm SPMI PMIC Temperature Alarm"
depends on OF && SPMI && IIO
select REGMAP_SPMI
help
This enables a thermal sysfs driver for Qualcomm plug-and-play (QPNP)
PMIC devices. It shows up in sysfs as a thermal sensor with multiple
trip points. The temperature reported by the thermal sensor reflects the
real time die temperature if an ADC is present or an estimate of the
temperature based upon the over temperature stage value.
config GENERIC_ADC_THERMAL
tristate "Generic ADC based thermal sensor"
depends on IIO
......
......@@ -29,7 +29,6 @@ thermal_sys-$(CONFIG_DEVFREQ_THERMAL) += devfreq_cooling.o
# platform thermal drivers
obj-y += broadcom/
obj-$(CONFIG_QCOM_SPMI_TEMP_ALARM) += qcom-spmi-temp-alarm.o
obj-$(CONFIG_SPEAR_THERMAL) += spear_thermal.o
obj-$(CONFIG_ROCKCHIP_THERMAL) += rockchip_thermal.o
obj-$(CONFIG_RCAR_THERMAL) += rcar_thermal.o
......
......@@ -9,3 +9,14 @@ config QCOM_TSENS
thermal zone device via the mode file results in disabling the sensor.
Also able to set threshold temperature for both hot and cold and update
when a threshold is reached.
config QCOM_SPMI_TEMP_ALARM
tristate "Qualcomm SPMI PMIC Temperature Alarm"
depends on OF && SPMI && IIO
select REGMAP_SPMI
help
This enables a thermal sysfs driver for Qualcomm plug-and-play (QPNP)
PMIC devices. It shows up in sysfs as a thermal sensor with multiple
trip points. The temperature reported by the thermal sensor reflects the
real time die temperature if an ADC is present or an estimate of the
temperature based upon the over temperature stage value.
obj-$(CONFIG_QCOM_TSENS) += qcom_tsens.o
qcom_tsens-y += tsens.o tsens-common.o tsens-8916.o tsens-8974.o tsens-8960.o tsens-v2.o
obj-$(CONFIG_QCOM_SPMI_TEMP_ALARM) += qcom-spmi-temp-alarm.o
......@@ -23,7 +23,7 @@
#include <linux/regmap.h>
#include <linux/thermal.h>
#include "thermal_core.h"
#include "../thermal_core.h"
#define QPNP_TM_REG_TYPE 0x04
#define QPNP_TM_REG_SUBTYPE 0x05
......
Markdown is supported
0% or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment