-
Add all clocks to give us the final video clocks within the Meson8, Meson8b and Meson8m2 SoCs. The final video clocks are: - cts_enct - cts_encl - cts_encp - cts_enci - cts_vdac0 - hdmi_tx_pixel - hdmi_sys Add multiple clocks in between which are needed to implement these clocks: - Opposed to GXBB there is no pre-multiplier for the PLL input. The assumption here is that the multiplier is required to achieve the HDMI 2.0 clock rates (which are up to twice the rate of the HDMI 1.4 rates). - The main PLL is called "HDMI PLL" or "HPLL" in the datasheet. Rename our existing "vid_pll_dco" to "hdmi_pll_dco". The actual VID_PLL clock also exists further down the tree. - Rename the existing "vid_pll" clock (which is the OD divider at HHI_VID_PLL_CNTL[17:16]) to "hdmi_pll_lvds_out" to match the naming from the datasheet. - Add the second OD divider called "hdmi_pll_hdmi_out" at HHI_VID_PLL_CNTL[19:18]. - Add the "vid_pll_in_sel" which can choose between "hdmi_pll_dco" and another parent. However, the second parent is not use on Amlogic's 3.10 kernel for HDMI or CVBS output so just leave a TODO in the code. - Add the "vid_pll_in_en" which is located after "vid_pll_in_sel" according to the datasheet. - Add "vid_pll_pre_div" which is used for divide-by-5 and divide-by-6 in Amlogic's 3.10 kernel sources. - Add "vid_pll_post_div" which divides the output of "vid_pll_pre_div" further down. The Amlogic 3.10 kernel configures this as divide-by-2 with "vid_pll_pre_div" being configured as divide-by-5 to achieve a total divider of 10. - Add the real "vid_pll" clock which selects between "vid_pll_pre_div", "vid_pll_post_div" and a third "vid_pll_pre_div_mult7_div2" (which is "vid_pll_pre_div" divided by 3.5). The latter is not supported yet because it's not used in Amlogic's 3.10 kernel. The "vid_pll" clock rate can also be measured by clkmsr to check whether this implementation is correct. - Add "vid_pll_final_div" which is a post-divider for "vid_pll" and it's used as input for "vclk" and "vclk2" - Add the two symmetric "vclk" and "vclk" clock trees, each with a divide-by-1, divide-by-2, divide-by-4, divide-by-6 and divide-by-12 clock and a divider for each clock. - Add the "cts_enct", "cts_encp" and "hdmi_tx_pixel" clocks which each have their own gate and can select between any of the five "vclk" dividers. - Add the "cts_encl" and "cts_vdac0" clocks which each have their own gate and can select between any of the five "vclk2" dividers. The "hdmi_sys" clock is a different than these video clocks. It takes "xtal" as input (there are three more but unknown parents). Add this clock as well as it's used by the HDMI controller. Amlogic's 3.10 kernel always configures this as "xtal divided by 1", so we can ignore the other parents for now. This was tested on Meson8b and Meson8m2 boards by comparing the common clock framework output with the clock measurer output. The following video modes were first set in u-boot (by running "video dev open $mode") before booting Linux: 4K2K30HZ (only supported by Meson8m2, not tested on Meson8b): - vid_pll: 297000000Hz - cts_encp: 297000000Hz - hdmi_tx_pixel: 297000000Hz 1080P: - vid_pll: 148500000Hz - cts_encp: 148500000Hz - hdmi_tx_pixel: 148500000Hz 720P: - vid_pll: 148500000Hz - cts_encp: 148500000Hz - hdmi_tx_pixel: 74250000Hz 480P: - vid_pll: 216000000Hz - cts_encp: 54000000Hz - hdmi_tx_pixel: 27000000Hz Signed-off-by:
Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by:
Neil Armstrong <narmstrong@baylibre.com> Link: https://lkml.kernel.org/r/20181202214220.7715-4-martin.blumenstingl@googlemail.com
6cb57c67
