1. 12 Oct, 2007 4 commits
  2. 11 May, 2007 1 commit
    • Tejun Heo's avatar
      libata: reimplement suspend/resume support using sdev->manage_start_stop · 9666f400
      Tejun Heo authored
      Reimplement suspend/resume support using sdev->manage_start_stop.
      
      * Device suspend/resume is now SCSI layer's responsibility and the
        code is simplified a lot.
      
      * DPM is dropped.  This also simplifies code a lot.  Suspend/resume
        status is port-wide now.
      
      * ata_scsi_device_suspend/resume() and ata_dev_ready() removed.
      
      * Resume now has to wait for disk to spin up before proceeding.  I
        couldn't find easy way out as libata is in EH waiting for the
        disk to be ready and sd is waiting for EH to complete to issue
        START_STOP.
      
      * sdev->manage_start_stop is set to 1 in ata_scsi_slave_config().
        This fixes spindown on shutdown and suspend-to-disk.
      Signed-off-by: default avatarTejun Heo <htejun@gmail.com>
      Signed-off-by: default avatarJeff Garzik <jeff@garzik.org>
      9666f400
  3. 01 May, 2007 1 commit
    • Tejun Heo's avatar
      libata: add deadline support to prereset and reset methods · d4b2bab4
      Tejun Heo authored
      Add @deadline to prereset and reset methods and make them honor it.
      ata_wait_ready() which directly takes @deadline is implemented to be
      used as the wait function.  This patch is in preparation for EH timing
      improvements.
      
      * ata_wait_ready() never does busy sleep.  It's only used from EH and
        no wait in EH is that urgent.  This function also prints 'be
        patient' message automatically after 5 secs of waiting if more than
        3 secs is remaining till deadline.
      
      * ata_bus_post_reset() now fails with error code if any of its wait
        fails.  This is important because earlier reset tries will have
        shorter timeout than the spec requires.  If a device fails to
        respond before the short timeout, reset should be retried with
        longer timeout rather than silently ignoring the device.
      
        There are three behavior differences.
      
        1. Timeout is applied to both devices at once, not separately.  This
           is more consistent with what the spec says.
      
        2. When a device passes devchk but fails to become ready before
           deadline.  Previouly, post_reset would just succeed and let
           device classification remove the device.  New code fails the
           reset thus causing reset retry.  After a few times, EH will give
           up disabling the port.
      
        3. When slave device passes devchk but fails to become accessible
           (TF-wise) after reset.  Original code disables dev1 after 30s
           timeout and continues as if the device doesn't exist, while the
           patched code fails reset.  When this happens, new code fails
           reset on whole port rather than proceeding with only the primary
           device.
      
        If the failing device is suffering transient problems, new code
        retries reset which is a better behavior.  If the failing device is
        actually broken, the net effect is identical to it, but not to the
        other device sharing the channel.  In the previous code, reset would
        have succeeded after 30s thus detecting the working one.  In the new
        code, reset fails and whole port gets disabled.  IMO, it's a
        pathological case anyway (broken device sharing bus with working
        one) and doesn't really matter.
      
      * ata_bus_softreset() is changed to return error code from
        ata_bus_post_reset().  It used to return 0 unconditionally.
      
      * Spin up waiting is to be removed and not converted to honor
        deadline.
      
      * To be on the safe side, deadline is set to 40s for the time being.
      Signed-off-by: default avatarTejun Heo <htejun@gmail.com>
      Signed-off-by: default avatarJeff Garzik <jeff@garzik.org>
      d4b2bab4
  4. 28 Apr, 2007 2 commits
  5. 02 Mar, 2007 1 commit
  6. 14 Feb, 2007 1 commit
  7. 09 Feb, 2007 5 commits
    • Sergei Shtylyov's avatar
      (2.6.20) pata_mpiix: probing cleanup (resend) · 92ae7849
      Sergei Shtylyov authored
      MPIIX has only single channel IDE which can be configured for either primary or
      secondary legacy I/O ports and IRQ.  So, get rid of the unneeded second probe
      entry in mpiix_init_one() and of the invalid (but unused anyway) enable bits in
      mpiix_pre_reset().
      
      Warning: this cleanup has only been compile-tested...
      Signed-off-by: default avatarSergei Shtylyov <sshtylyov@ru.mvista.com>
      Signed-off-by: default avatarJeff Garzik <jeff@garzik.org>
      92ae7849
    • Sergei Shtylyov's avatar
      (2.6.20) pata_mpiix: fix PIO setup issues · 7b4f1a13
      Sergei Shtylyov authored
      Fix clearing/setting the wrong TIME/IE/PPE bits for a slave drive caused by a
      wrong shift count.
      Fix the PIO mode 1 being overclocked by wrongly selecting the fast timing bank.
      Also, fix/rephrase some comments while at it.
      Signed-off-by: default avatarSergei Shtylyov <sshtylyov@ru.mvista.com>
      Signed-off-by: default avatarJeff Garzik <jeff@garzik.org>
      7b4f1a13
    • Akira Iguchi's avatar
      libata: add another IRQ calls (libata drivers) · 246ce3b6
      Akira Iguchi authored
      This patch is against each libata driver.
      
      Two IRQ calls are added in ata_port_operations.
      - irq_on() is used to enable interrupts.
      - irq_ack() is used to acknowledge a device interrupt.
      
      In most drivers, ata_irq_on() and ata_irq_ack() are used for
      irq_on and irq_ack respectively.
      
      In some drivers (ex: ahci, sata_sil24) which cannot use them
      as is, ata_dummy_irq_on() and ata_dummy_irq_ack() are used.
      Signed-off-by: default avatarKou Ishizaki <kou.ishizaki@toshiba.co.jp>
      Signed-off-by: default avatarAkira Iguchi <akira2.iguchi@toshiba.co.jp>
      Signed-off-by: default avatarJeff Garzik <jeff@garzik.org>
      246ce3b6
    • Tejun Heo's avatar
      libata: convert to iomap · 0d5ff566
      Tejun Heo authored
      Convert libata core layer and LLDs to use iomap.
      
      * managed iomap is used.  Pointer to pcim_iomap_table() is cached at
        host->iomap and used through out LLDs.  This basically replaces
        host->mmio_base.
      
      * if possible, pcim_iomap_regions() is used
      
      Most iomap operation conversions are taken from Jeff Garzik
      <jgarzik@pobox.com>'s iomap branch.
      Signed-off-by: default avatarTejun Heo <htejun@gmail.com>
      Signed-off-by: default avatarJeff Garzik <jeff@garzik.org>
      0d5ff566
    • Tejun Heo's avatar
      libata: update libata LLDs to use devres · 24dc5f33
      Tejun Heo authored
      Update libata LLDs to use devres.  Core layer is already converted to
      support managed LLDs.  This patch simplifies initialization and fixes
      many resource related bugs in init failure and detach path.  For
      example, all converted drivers now handle ata_device_add() failure
      gracefully without excessive resource rollback code.
      
      As most resources are released automatically on driver detach, many
      drivers don't need or can do with much simpler ->{port|host}_stop().
      In general, stop callbacks are need iff port or host needs to be given
      commands to shut it down.  Note that freezing is enough in many cases
      and ports are automatically frozen before being detached.
      Signed-off-by: default avatarTejun Heo <htejun@gmail.com>
      Signed-off-by: default avatarJeff Garzik <jeff@garzik.org>
      24dc5f33
  8. 03 Dec, 2006 1 commit
  9. 02 Dec, 2006 1 commit
  10. 29 Nov, 2006 1 commit
  11. 29 Sep, 2006 1 commit
  12. 26 Sep, 2006 1 commit
  13. 29 Aug, 2006 1 commit