Commit cbc59e26 authored by Baruch Siach's avatar Baruch Siach Committed by Linus Walleij

pinctrl: dt-binding: document Conexant CX92755 SoC

Add pinctrl device tree binding documentation for the General Purpose Pin
Mapping module of the Conexant CX92755 SoC.
Signed-off-by: default avatarBaruch Siach <baruch@tkos.co.il>
Signed-off-by: Linus Walleij's avatarLinus Walleij <linus.walleij@linaro.org>
parent ab4a9362
Conexant Digicolor CX92755 General Purpose Pin Mapping
This document describes the device tree binding of the pin mapping hardware
modules in the Conexant Digicolor CX92755 SoCs. The CX92755 in one of the
Digicolor series of SoCs.
=== Pin Controller Node ===
Required Properties:
- compatible: Must be "cnxt,cx92755-pinctrl"
- reg: Base address of the General Purpose Pin Mapping register block and the
size of the block.
- gpio-controller: Marks the device node as a GPIO controller.
- #gpio-cells: Must be <2>. The first cell is the pin number and the
second cell is used to specify flags. See include/dt-bindings/gpio/gpio.h
for possible values.
For example, the following is the bare minimum node:
pinctrl: pinctrl@f0000e20 {
compatible = "cnxt,cx92755-pinctrl";
reg = <0xf0000e20 0x100>;
gpio-controller;
#gpio-cells = <2>;
};
As a pin controller device, in addition to the required properties, this node
should also contain the pin configuration nodes that client devices reference,
if any.
For a general description of GPIO bindings, please refer to ../gpio/gpio.txt.
=== Pin Configuration Node ===
Each pin configuration node is a sub-node of the pin controller node and is a
container of an arbitrary number of subnodes, called pin group nodes in this
document.
Please refer to the pinctrl-bindings.txt in this directory for details of the
common pinctrl bindings used by client devices, including the definition of a
"pin configuration node".
=== Pin Group Node ===
A pin group node specifies the desired pin mux for an arbitrary number of
pins. The name of the pin group node is optional and not used.
A pin group node only affects the properties specified in the node, and has no
effect on any properties that are omitted.
The pin group node accepts a subset of the generic pin config properties. For
details generic pin config properties, please refer to pinctrl-bindings.txt
and <include/linux/pinctrl/pinconfig-generic.h>.
Required Pin Group Node Properties:
- pins: Multiple strings. Specifies the name(s) of one or more pins to be
configured by this node. The format of a pin name string is "GP_xy", where x
is an uppercase character from 'A' to 'R', and y is a digit from 0 to 7.
- function: String. Specifies the pin mux selection. Values must be one of:
"gpio", "client_a", "client_b", "client_c"
Example:
pinctrl: pinctrl@f0000e20 {
compatible = "cnxt,cx92755-pinctrl";
reg = <0xf0000e20 0x100>;
uart0_default: uart0_active {
data_signals {
pins = "GP_O0", "GP_O1";
function = "client_b";
};
};
};
uart0: uart@f0000740 {
compatible = "cnxt,cx92755-usart";
...
pinctrl-0 = <&uart0_default>;
pinctrl-names = "default";
};
In the example above, a single pin group configuration node defines the
"client select" for the Rx and Tx signals of uart0. The uart0 node references
that pin configuration node using the &uart0_default phandle.
Markdown is supported
0% or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment