Commit 8c58f1a7 authored by Jacopo Mondi's avatar Jacopo Mondi Committed by Linus Walleij

pinctrl: generic: Add bi-directional and output-enable

Add bi-directional and output-enable pin configuration properties.

bi-directional allows to specify when a pin shall operate in input and
output mode at the same time. This is particularly useful in platforms
where input and output buffers have to be manually enabled.

output-enable is just syntactic sugar to specify that a pin shall
operate in output mode, ignoring the provided argument.
This pairs with input-enable pin configuration option.
Signed-off-by: default avatarJacopo Mondi <jacopo+renesas@jmondi.org>
Acked-by: Rob Herring's avatarRob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij's avatarLinus Walleij <linus.walleij@linaro.org>
parent 03ffb507
......@@ -247,6 +247,7 @@ bias-bus-hold - latch weakly
bias-pull-up - pull up the pin
bias-pull-down - pull down the pin
bias-pull-pin-default - use pin-default pull state
bi-directional - pin supports simultaneous input/output operations
drive-push-pull - drive actively high and low
drive-open-drain - drive with open drain
drive-open-source - drive with open source
......@@ -259,6 +260,7 @@ input-debounce - debounce mode with debound time X
power-source - select between different power supplies
low-power-enable - enable low power mode
low-power-disable - disable low power mode
output-enable - enable output on pin regardless of output value
output-low - set the pin to output mode with low level
output-high - set the pin to output mode with high level
slew-rate - set the slew rate
......
......@@ -35,6 +35,7 @@ static const struct pin_config_item conf_items[] = {
PCONFDUMP(PIN_CONFIG_BIAS_PULL_PIN_DEFAULT,
"input bias pull to pin specific state", NULL, false),
PCONFDUMP(PIN_CONFIG_BIAS_PULL_UP, "input bias pull up", NULL, false),
PCONFDUMP(PIN_CONFIG_BIDIRECTIONAL, "bi-directional pin operations", NULL, false),
PCONFDUMP(PIN_CONFIG_DRIVE_OPEN_DRAIN, "output drive open drain", NULL, false),
PCONFDUMP(PIN_CONFIG_DRIVE_OPEN_SOURCE, "output drive open source", NULL, false),
PCONFDUMP(PIN_CONFIG_DRIVE_PUSH_PULL, "output drive push pull", NULL, false),
......@@ -160,6 +161,7 @@ static const struct pinconf_generic_params dt_params[] = {
{ "bias-pull-up", PIN_CONFIG_BIAS_PULL_UP, 1 },
{ "bias-pull-pin-default", PIN_CONFIG_BIAS_PULL_PIN_DEFAULT, 1 },
{ "bias-pull-down", PIN_CONFIG_BIAS_PULL_DOWN, 1 },
{ "bi-directional", PIN_CONFIG_BIDIRECTIONAL, 1 },
{ "drive-open-drain", PIN_CONFIG_DRIVE_OPEN_DRAIN, 0 },
{ "drive-open-source", PIN_CONFIG_DRIVE_OPEN_SOURCE, 0 },
{ "drive-push-pull", PIN_CONFIG_DRIVE_PUSH_PULL, 0 },
......@@ -172,6 +174,7 @@ static const struct pinconf_generic_params dt_params[] = {
{ "input-schmitt-enable", PIN_CONFIG_INPUT_SCHMITT_ENABLE, 1 },
{ "low-power-disable", PIN_CONFIG_LOW_POWER_MODE, 0 },
{ "low-power-enable", PIN_CONFIG_LOW_POWER_MODE, 1 },
{ "output-enable", PIN_CONFIG_OUTPUT, 1, },
{ "output-high", PIN_CONFIG_OUTPUT, 1, },
{ "output-low", PIN_CONFIG_OUTPUT, 0, },
{ "power-source", PIN_CONFIG_POWER_SOURCE, 0 },
......
......@@ -42,6 +42,8 @@
* @PIN_CONFIG_BIAS_PULL_UP: the pin will be pulled up (usually with high
* impedance to VDD). If the argument is != 0 pull-up is enabled,
* if it is 0, pull-up is total, i.e. the pin is connected to VDD.
* @PIN_CONFIG_BIDIRECTIONAL: the pin will be configured to allow simultaneous
* input and output operations.
* @PIN_CONFIG_DRIVE_OPEN_DRAIN: the pin will be driven with open drain (open
* collector) which means it is usually wired with other output ports
* which are then pulled up with an external resistor. Setting this
......@@ -96,6 +98,7 @@ enum pin_config_param {
PIN_CONFIG_BIAS_PULL_DOWN,
PIN_CONFIG_BIAS_PULL_PIN_DEFAULT,
PIN_CONFIG_BIAS_PULL_UP,
PIN_CONFIG_BIDIRECTIONAL,
PIN_CONFIG_DRIVE_OPEN_DRAIN,
PIN_CONFIG_DRIVE_OPEN_SOURCE,
PIN_CONFIG_DRIVE_PUSH_PULL,
......
Markdown is supported
0% or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment