Commit 8b8b091b authored by Tony Lindgren's avatar Tony Lindgren Committed by Linus Walleij

pinctrl: Add one-register-per-pin type device tree based pinctrl driver

Add one-register-per-pin type device tree based pinctrl driver.

This driver has been tested on omap2+ series of processors,
where there is either an 8 or 16-bit padconf register for each pin.
Support for other similar pinmux controllers can be added.
Signed-off-by: default avatarTony Lindgren <>
Signed-off-by: Linus Walleij's avatarLinus Walleij <>
parent 3923040b
One-register-per-pin type device tree based pinctrl driver
Required properties:
- compatible : "pinctrl-single"
- reg : offset and length of the register set for the mux registers
- pinctrl-single,register-width : pinmux register access width in bits
- pinctrl-single,function-mask : mask of allowed pinmux function bits
in the pinmux register
Optional properties:
- pinctrl-single,function-off : function off mode for disabled state if
available and same for all registers; if not specified, disabling of
pin functions is ignored
This driver assumes that there is only one register for each pin,
and uses the common pinctrl bindings as specified in the pinctrl-bindings.txt
document in this directory.
The pin configuration nodes for pinctrl-single are specified as pinctrl
register offset and value pairs using pinctrl-single,pins. Only the bits
specified in pinctrl-single,function-mask are updated. For example, setting
a pin for a device could be done with:
pinctrl-single,pins = <0xdc 0x118>;
Where 0xdc is the offset from the pinctrl register base address for the
device pinctrl register, and 0x118 contains the desired value of the
pinctrl register. See the device example and static board pins example
below for more information.
/* SoC common file */
/* first controller instance for pins in core domain */
pmx_core: pinmux@4a100040 {
compatible = "pinctrl-single";
reg = <0x4a100040 0x0196>;
#address-cells = <1>;
#size-cells = <0>;
pinctrl-single,register-width = <16>;
pinctrl-single,function-mask = <0xffff>;
/* second controller instance for pins in wkup domain */
pmx_wkup: pinmux@4a31e040 {
compatible = "pinctrl-single;
reg = <0x4a31e040 0x0038>;
#address-cells = <1>;
#size-cells = <0>;
pinctrl-single,register-width = <16>;
pinctrl-single,function-mask = <0xffff>;
/* board specific .dts file */
&pmx_core {
* map all board specific static pins enabled by the pinctrl driver
* itself during the boot (or just set them up in the bootloader)
pinctrl-names = "default";
pinctrl-0 = <&board_pins>;
board_pins: pinmux_board_pins {
pinctrl-single,pins = <
0x6c 0xf
0x6e 0xf
0x70 0xf
0x72 0xf
/* map uart2 pins */
uart2_pins: pinmux_uart2_pins {
pinctrl-single,pins = <
0xd8 0x118
0xda 0
0xdc 0x118
0xde 0
&uart2 {
pinctrl-names = "default";
pinctrl-0 = <&uart2_pins>;
......@@ -102,6 +102,14 @@ config PINCTRL_PXA910
select PINCTRL_PXA3xx
select PINCONF
tristate "One-register-per-pin type device tree based pinctrl driver"
depends on OF
select PINMUX
select PINCONF
This selects the device tree based generic pinctrl driver.
bool "CSR SiRFprimaII pin controller driver"
depends on ARCH_PRIMA2
......@@ -22,6 +22,7 @@ obj-$(CONFIG_PINCTRL_NOMADIK) += pinctrl-nomadik.o
obj-$(CONFIG_PINCTRL_DB8500) += pinctrl-nomadik-db8500.o
obj-$(CONFIG_PINCTRL_PXA168) += pinctrl-pxa168.o
obj-$(CONFIG_PINCTRL_PXA910) += pinctrl-pxa910.o
obj-$(CONFIG_PINCTRL_SINGLE) += pinctrl-single.o
obj-$(CONFIG_PINCTRL_SIRF) += pinctrl-sirf.o
obj-$(CONFIG_PINCTRL_TEGRA) += pinctrl-tegra.o
obj-$(CONFIG_PINCTRL_TEGRA20) += pinctrl-tegra20.o
This diff is collapsed.
Markdown is supported
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment