Commit e6ba136a authored by 83.24.62.236's avatar 83.24.62.236

remove it and replace with the content of Randr12Howto

parent d08be572
= Randr 1.2 Nouveau Status =
== Enabling Randr12 support in nouveau ==
Randr 1.2 is now enabled by default in the git master branch. Dual head support probably mostly works. See the FeatureMatrix about supported cards.
Randr 1.2 is used by Nouveau. No need to explicitly enable it, and you cannot disable it.
There is the [[https://bugs.freedesktop.org/show_bug.cgi?id=14405|randr-1.2 bug tracker]], which should depend on all randr-1.2 related bugs. This does not include the g80 support, which is entirely seperate. If anyone wishes to do some work for those cards, then that is certainly welcome.
== Generic HowTos ==
* Simple step-by-step guide to create a very clean Randr12-based config file with all old junk removed:
* http://wiki.debian.org/XStrikeForce/HowToRandR12
* Very nice illustrations but lots of examples which you'll not apply to Nouveau, like TV output support:
* http://www.thinkwiki.org/wiki/Xorg_RandR_1.2
How to use randr-1.2 features: Randr12Howto.
== Dual Head setup ==
=== xorg.conf ===
==== Sections and configuration settings to remove ====
Randr 1.2 does not use multiple Screen sections, so if you have those you have to remove them from your xorg.conf :
* If you have two sections like these, remove one of these sections (in this example Screen1): {{{
Section "Screen"
Identifier "Screen0"
...
== Currently tested ==
Section "Screen" <==== Remove this second section, if you have sone (start removing lines here)
Identifier "Screen1"
...
EndSection (stop removing lines here)
* Nothing is broken by default, but be sure to test.
}}}
* If you have a Option "MonitorLayout" or/and "Screen" options in the Device section, remove them
* Also remove the second Screen entry from the ServerLayout section. Example : {{{
Screen 0 "Screen0" 1680 0
Screen 1 "Screen1" LeftOf "Screen0" <= remove this one (for Screen1)
}}}
* Also remove any RightOf/LeftOf indications from the remaining Screen line in the ServerLayout section (see above)
* The Geforce6 and 7 cards are doing quite well.
==== Settings on xorg.conf for Randr12 ====
If you do not preconfigure a left/right/above/below setup in your xorg.xonf (see next section) add {{{Virtual x y}}} to your Display Section: {{{
Section "Screen"
Identifier "Your Screen identifier here"
DefaultDepth 24
SubSection "Display"
Depth 24
Virtual 3360 1050
EndSubSection
Device "Your Device identifier here"
EndSection
}}}
The example above configures a framebuffer for two monitors, each using resolutions up to 1680x1050 pixels, put side-by-side dynamically, after you started X. The values are calculated like this:
{{{ Virtual <witdh of the two monitors, e.g. 1680+1680=3360> <maxium height to used by the montiors, e.g. 1050>
}}}
Only the part which the monitors show is used: You can start and use X with one monitor as ususal but later add a new monitor and use {{{xrandr}}} with {{{--leftof}}} or {{{--rightof}}} to place the new monitor left or right of your primary monitor.
==== Preconfigured side-by-side (LeftOf/RightOf) setup thru xorg.conf ====
If you have done the above, you can also preconfigure the two monitors to be side-by-side right from the X startup. With this, you do not even need the "Virtual <x> <y>" line because then, the X server already knows before starting that it has to allocate a virtual framebuffer which fits both Monitors side-by-side.
* On G80, the hotplug is not working. Note that the g80 code is seperate and i wouldn't recommend using nouveau on g80 for anything other than development.
You need to make the following changes for this to work (simplest way):
* Change the Monitor identifiers in your xorg.conf to the identifiers which "xrandr" reports and add a LeftOf/RightOf to one of the Monitor sections. Example: {{{
Section "Monitor"
Identifier "DVI-D-0"
...
Section "Monitor"
Identifier "VGA-0"
...
Option "LeftOf" "DVI-D-0"
}}}
Then restart X and enjoy :-)
== Examples for the usage of the Xorg xrandr tool to manipulate the monitor setup ==
Usage: {{{xrandr -h}}} gives a short list of available options, {{{man xrandr}}} shows you the xrandr manual.
When Randr12 is enabled, you can check the current Randr12 configuration with with {{{xrandr -q}}} (or no options): {{{
xrandr -q
Screen 0: minimum 320 x 200, current 2960 x 1050, maximum 3000 x 1050
DVI-A-0 disconnected (normal left inverted right x axis y axis)
DVI-D-0 connected 1680x1050+0+0 (normal left inverted right x axis y axis) 474mm x 296mm
1680x1050 60.0*+
1280x1024 75.0 59.9
1280x960 59.9
1152x864 75.0 74.8
1024x768 75.1 70.1 60.0
832x624 74.6
800x600 72.2 75.0 60.3 56.2
640x480 75.0 72.8 66.7 60.0
720x400 70.1
VGA-0 connected 1280x1024+1680+0 (normal left inverted right x axis y axis) 350mm x 262mm
1280x1024 84.8* 75.0
1152x864 75.0
1024x768 84.9 75.1 70.1 60.0 59.9 43.5
832x624 74.6
800x600 84.9 72.2 75.0 60.3 56.2
640x480 84.6 75.0 72.8 74.8 66.7 60.0
720x405 69.6
720x400 87.8 70.1
}}}
Change the mode of an output using: {{{
xrandr --output <output> --mode <mode to switch to>
}}}
To turn a newly connected monitor on, use {{{
xrandr --output <display> --auto
}}} or {{{
xrandr --output <output> --mode ...x...
}}}
To turn an output off: {{{
xrandr --output <output> --off
}}}
To make an output show the same screen area as an other output (cloned mode, default with Randr12): {{{
xrandr --output <output to change> --same-as <output you want to clone>
}}}
To put the display of one output left, right, above or below to the display of an existing output use ''--left-of, --right-of, --above, --below'' : {{{
xrandr --output <output to change> [ --left-of |--right-of | --above | --below ] <output which shall keep its position>
}}}
More xrandr examples are found in the generic Randr12 howtos mentioned on the top of this page.
Markdown is supported
0% or .
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment