Stdout
Using IGT_SRANDOM=1712821676 for randomisation
Opened device: /dev/dri/card1
runner: This test was killed due to a kernel taint (0x240).
Stderr
Received signal SIGQUIT.
Stack trace:
#0 [fatal_sig_handler+0x10f]
#1 [killpg+0x40]
#2 [ioctl+0x9]
#3 [drmIoctl+0x30]
#4 [__syncobj_wait+0x2c]
#5 [syncobj_wait_err+0x3b]
#6 [__intel_ctx_xe_exec+0x114]
#7 [intel_ctx_xe_exec+0xd]
#8 [blt_block_copy+0x210]
#9 [blitcopy+0x20a]
#10 [setup_linear_mapping+0x1e3]
#11 [create_cairo_surface__gpu+0x32]
#12 [igt_get_cairo_surface+0x9b]
#13 [igt_get_cairo_ctx+0x10]
#14 [create_cursor_fb+0x72]
#15 [run_size_tests.constprop.0+0x342]
#16 [run_tests_on_pipe.constprop.0+0x248]
#17 [__igt_unique____real_main1053+0x1ba]
#18 [main+0x3a]
#19 [__libc_start_main+0xf3]
#20 [_start+0x2e]
Dmesg
<7> [456.336541] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off
<7> [456.336672] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6
<7> [456.336739] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02
<6> [456.379885] Console: switching to colour dummy device 80x25
<6> [456.380367] [IGT] kms_cursor_crc: executing
<7> [456.389161] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:194:DP-4]
<7> [456.389199] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:194:DP-4]
<7> [456.389352] xe 0000:00:02.0: [drm:intel_tc_port_update_mode [xe]] Port D/TC#1: TC port mode reset (disconnected -> tbt-alt)
<7> [456.389435] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:194:DP-4] disconnected
<7> [456.389810] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:206:DP-5]
<7> [456.389825] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:206:DP-5]
<7> [456.389933] xe 0000:00:02.0: [drm:intel_tc_port_update_mode [xe]] Port E/TC#2: TC port mode reset (disconnected -> tbt-alt)
<7> [456.390005] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:206:DP-5] disconnected
<7> [456.390346] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:214:DP-6]
<7> [456.390357] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:214:DP-6]
<7> [456.390448] xe 0000:00:02.0: [drm:intel_tc_port_update_mode [xe]] Port F/TC#3: TC port mode reset (disconnected -> tbt-alt)
<7> [456.390510] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:214:DP-6] disconnected
<7> [456.390928] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:185:eDP-2]
<7> [456.390944] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:185:eDP-2]
<7> [456.391587] xe 0000:00:02.0: [drm:intel_dp_read_dsc_dpcd [xe]] DSC DPCD: 00 11 00 76 0b 01 01 80 00 01 06 66 08 00 00 00
<7> [456.391669] xe 0000:00:02.0: [drm:intel_dp_print_rates [xe]] source rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 675000, 810000
<7> [456.391736] xe 0000:00:02.0: [drm:intel_dp_print_rates [xe]] sink rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000
<7> [456.391799] xe 0000:00:02.0: [drm:intel_dp_print_rates [xe]] common rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000
<7> [456.391900] xe 0000:00:02.0: [drm:update_display_info [drm]] [CONNECTOR:185:eDP-2] Supported Monitor Refresh rate range is 40 Hz - 120 Hz
<7> [456.391949] [drm:__displayid_iter_next [drm]] base revision 0x13, length 121, 0 0
<5> [456.391974] [drm] DisplayID checksum invalid, remainder is 248
<7> [456.391976] [drm:__displayid_iter_next [drm]] base revision 0x13, length 121, 0 0